Wasserdichter 2x AA-Batteriehalter mit Ein/Aus-Schalter

CHF 831.00*

Content: 1 Stück

Prices incl. VAT plus shipping costs

Available. If the available stock is exceeded, no additional units of this item can be added to the cart. If you have any questions, please contact the service hotline at the bottom of this page.

Schachtel

Product number: ADA-770

Product information "Wasserdichter 2x AA-Batteriehalter mit Ein/Aus-Schalter"

Keep your power source safe and toasty in these waterproof 2xAA battery holders. They're just like classic switched battery holders, but designed for survival! The case has a rubber gasket around the edge of the case (its black and hard to see in the photos but it is there) and attaches together with 4 machine screws. What we like about this design is that the hexnuts are captive in one side and you can assemble/disassemble as many times as you need. There's a rubber-boot on-off switch (press to turn on/off). Use with any alkaline or rechargeable batteries for about 3V output.

We also have a 3xAA version when you need a little more power

Technical Details

Dimensions: 68mm x 33mm x 19mm / 2.7" x 1.3" x 0.75"
Wire Length: 149.5mm / 5.88"
Weight: 26.10 grams

Fachbereich:	Medien & Informatik - M&I

0 of 0 reviews

Leave a review!

Share your experiences with other customers.

Login

Your email address

Your password

Display reviews in current language only.

No reviews found. Share your insights with others.

Similar Items

4 x AA Battery Holder with On/Off Switch

Make a nice portable power pack with this 4 x AA battery holder. It fits any alkaline or rechargeable AA batteries in series. There's a snap on cover and an on/off switch which can be handy when wiring to something without a switch. New! We now have 0.1" headers on ends of these cables so you can plug them into a breadboard or headers with ease! Of course, you can still always solder to them or cut the ends off. The four batteries are held in series, for a nominal output of 6V DC for alkaline (6.4V when fresh, 4V when dead), and 4.8V DC for rechargeables (5.2V when fully charged, 4.4V when discharged). Using rechargeables will make this work nicely with nearly any 5V project, with alkalines you may want to put a 1N4001 in series to drop the voltage from 6V down to 5.3V.

CHF 514.00*

Details

3x AA Battery Box with Switch and Connector

This 3x AA battery, switched battery holder come compete with a terminal connector on the end of the wires. These are perfect for connecting LEDs without the need for soldering. The batteries are fully enclosed in plastic case, which is secured in place by a small screw. The unit incorporates a small on / off switch. The leads are approximately 130mm in length and colour red and black to show the polarity of the connector.

CHF 2.00*

Nähbarer CR2032-Batteriehalter

This battery holder is by far the easiest way to add a battery to a small wearable project. By coincidence, there are two small 1mm diameter holes in the metal connection tabs, just large enough for a #5 or smaller needle to pass through. One tab connects to common ground (negative) and the other tab is +3 Volts. This holder is meant to be used with Lithium CR2032 (20mm diameter, 3.2mm thick) sized coin batteries. These are almost always 3V at about 200+ mAh capacity.Lithium coin cells are not rechargeable but they are very easy to find, available at any grocery store. Inserting the coin is easy, the holder is very sturdy, and it snaps out with a push. Its got a nice flat plastic back that you can easily glue in place for extra mechanical stability.

CHF 395.00*

Wasserdichter 3x AA-Batteriehalter mit Ein/Aus-Schalter

Keep your power source safe and toasty in these waterproof 3xAA battery holders. They're just like classic switched battery holders, but designed for survival! The case has a rubber gasket around the edge of the case (its black and hard to see in the photos but it is there) and attaches together with 4 machine screws. What we like about this design is that the hexnuts are captive in one side and you can assemble/disassemble as many times as you need. There's a potted power switch and a rubber-boot on-off switch (press to turn on/off). Use with any alkaline or rechargeable batteries for about 4.5V output.

CHF 779.00*

Details