Nadel-Set

Bildungsstufe:	Scuola elementare, Scuola media
Fach:	e-Textiles, ed. manuale e tecnica, ed. manuale e tecnica

LilyTwinkle

LilyTwinkle è una piccola scheda LilyPad progettata per aggiungere un po' di scintillio al tuo progetto. Anche se è piccola come alcuni dei sensori LilyPad, questa scheda è dotata di un microcontrollore ATtiny e quindi è piuttosto intelligente! Basta cucire 4 LED e collegare una batteria per farli scintillare (un po' come le lucciole... o gli insetti luminosi, se così li chiamate). LilyTwinkle è un modo semplice e veloce per aggiungere luci scintillanti a un progetto senza bisogno di programmazione o di una scheda principale ingombrante. Se siete utenti avanzati e volete riprogrammare LilyTwinkle, i connettori di programmazione ICSP si trovano sul retro. LilyPad è una tecnologia e-textile indossabile sviluppata da Leah Buechley e progettata in collaborazione da Leah e SparkFun. Ogni LilyPad è stato progettato in modo creativo per avere ampi cuscinetti di collegamento che ne consentono la cucitura nei vestiti. Sono disponibili diverse schede di ingresso, uscita, alimentazione e sensori. Nota: una parte di questa vendita viene restituita alla dottoressa Leah Buechley per il continuo sviluppo e la formazione sugli e-textiles.

CHF 1’138.00*

LilyPad LED White (5pcs)

This is a simple pack of five White LilyPad LEDs that are still attached to one another, letting you snap the LEDs apart at your leisure to sew into clothing or whatever else you can dream up. LilyPad is a wearable e-textile technology developed by Dr. Leah Buechley and cooperatively designed by Leah and SparkFun. Each LilyPad piece was creatively designed with large sew tabs to allow them to be sewn into fabric. Various input, output, power and sensor boards are available. They're even washable (with special care)! Note: A portion of this sale is given back to Dr. Buechley for continued development and education in e-textiles.

Contenuto: 5 Paket(e) (CHF 1.25* / 1 Paket(e))

CHF 6.25*

Dettagli

Lilypad Conductive Thread Bobbin

This is 12 meters of smooth conductive thread spun from stainless steel fiber and wound on a plastic bobbin. Use it to sew up all of your e-textile projects. This small bobbin is a great way to get into wearable electronics without the upfront cost of buying an entire spool of thread. Close to 40 feet of thread is enough to get a simple design stitched onto your shirt, backpack or hat. What sets this thread apart from the other conductive thread that we carry is the fact that it’s actually spun from 12UM stainless steel fiber making it incredibly smooth and without the loose hairs seen on other bobbins. This means that while it may not be easy to solder to, because it’s stainless, it also won’t burn up when you touch it with a soldering iron. Suitable for hand or machine sewing (as a bobbin thread). We’ve had no trouble using it for close, tight connections, but if you’re worried, waxing the thread should keep it manageable!

CHF 9.95*

LilyPad Temperature Sensor

Detecting temperature changes has never been easier. The MCP9700 is a small thermistor type temperature sensor. This sensor will output 0.5V at 0 degrees C, 0.75V at 25 C, and 10mV per degree C. Doing an analog to digital conversion on the signal line will allow you to establish the local ambient temperature. Detect physical touch based on body heat and ambient conditions with this small sensor. LilyPad is a wearable e-textile technology developed by Leah Buechley and cooperatively designed by Leah and SparkFun. Each LilyPad was creatively designed to have large connecting pads to allow them to be sewn into clothing. Various input, output, power, and sensor boards are available. They’re even washable! Note: A portion of this sale is given back to Dr. Leah Buechley for continued development and education of e-textiles.

CHF 10.00*

LilyPad ProtoSnap Plus

The LilyPad ProtoSnap Plus is a sewable electronics prototyping board that you can use to explore circuits and programming, then break apart to make an interactive fabric or wearable project. Programming the ProtoSnap Plus is easy with the free Arduino software you’ll need to program the ATmega32U4 on LilyPad USB Plus at the heart of the board. Once you’ve installed the software, you’ll be able to write and upload your own programs to the board, making it do almost anything you want. At the center of the ProtoSnap Plus is the LilyPad USB Plus microcontroller, pre-wired to a LilyPad board including a LilyPad Light Sensor, LilyPad Buzzer, LilyPad Button Board, four pairs of colored LilyPad LEDs and a LilyPad Slide Switch. Because these components are connected together on the ProtoSnap board, you can test out your project ideas before you sew. The ProtoSnap Plus also includes expansion ports that let you sew your wearables together or use alligator cables to easily connect external sensors and components. After testing out your coding ideas using the attached LilyPad pieces, you can break apart the prototyping board and sew them into your project! Please be aware that the Lilypad ProtoSnap Plus is NOT supported on Windows 7/8 due to a lack of support drivers for those specific OS’s. Note: A portion of this sale is given back to Dr. Leah Buechley for continued development and education in e-textiles.

CHF 101.81*

Electro-Fashion conductive thread, 50 yards/ 45m

This is Kitronik's very own Electro-Fashion® branded Conductive Thread and we think it is among the best conductive thread available. It is perfect for hand sewing and can also be used on the bottom bobbin of a sewing machine (this will require the thread to be wound on to the smaller bottom bobbin first). Conductive thread can be used like conventional sewing yarn, however it electrically conducts allowing electronics to be integrated into textiles. This makes it ideal for use in a range of e-textile applications. The thread is nano plated with silver to make it conductive. The conductive thread has a generally low resistance but it does vary. We have measured between 40 and 160 ohms per meter, depending on the tension the thread is under. Once sewn the resistance is typically in the middle of this range. Over time the silver plating will degrade particularly if washed and we have measured in excess of 280 ohms on some of our older examples. Resistance does not vary significantly from one length of thread to the next, so you should be able to use this thread without concern for "dead" sections. The conductive thread has a breaking strain of around 9.3 pounds (4.2 kilos). It comprises roughly 96 individual filaments, each coated with a micron-thick layer of natural silver. This plating of the yarn is done in Europe to ensure as high a quality finish as possible. In construction, 16 of these filaments are wound together to form an initial twist; two of these twists are then twisted together, and finally three of these twists are combined to form the finished thread. The conductive thread is approximately 18 denier. It is heavier than a regular sewing thread, but not as heavy as an upholstery thread. It can be sewn on most domestic sewing machines using either a regular needle or the next size up. This thread does not fray. Features: No (or very low) fray. Conductivity = approximately 40Ω per metre (12.2Ω per foot). Count = 875 dTex. Strength 3000 cN. Elongation at break = 37%. Twist = 240Z-380S. Contents: 1 x Reel Electro-Fashion®, Conductive Thread, 50 yards / 45m.

CHF 13.50*

Dettagli

LilyTwinkle ProtoSnap

The ProtoSnap series is a new way to prototype your project without a breadboard. Everything is wired together on a single board, which makes it easy to explore the possibilities of the components before snapping them apart and building them into your project. The ProtoSnap LilyTwinkle board is a very simple way to jump right into e-textiles. By including the LilyTwinkle, a coin cell battery holder (with built-in switch), and four white LEDs the ProtoSnap LilyTwinkle board easily allows you to add some sparkle to any project. To make your e-textile experience all the more enjoyable we have added a needle set and 30 feet of conductive thread! Note: A portion of this sale is given back to Dr. Leah Buechley for continued development and education of e-textiles and also to Arduino LLC to help fund continued development of new tools and new IDE features.

CHF 3’013.00*

Dettagli

Electro-Fashion conductive thread, 250 m

This is Kitronik's very own Electro-Fashion® branded Conductive Thread and we think it is among the best conductive thread available. It is perfect for hand sewing and can also be used on the bottom bobbin of a sewing machine (this will require the thread to be wound on to the smaller bottom bobbin first). Conductive thread can be used like conventional sewing yarn, however it electrically conducts allowing electronics to be integrated into textiles. This makes it ideal for use in a range of e-textile applications. The thread is nano plated with silver to make it conductive. The conductive thread has a generally low resistance but it does vary. We have measured between 40 and 160 ohms per meter, depending on the tension the thread is under. Once sewn the resistance is typically in the middle of this range. Over time the silver plating will degrade particularly if washed and we have measured in excess of 280 ohms on some of our older examples. Resistance does not vary significantly from one length of thread to the next, so you should be able to use this thread without concern for "dead" sections. The conductive thread has a breaking strain of around 9.3 pounds (4.2 kilos). It comprises roughly 96 individual filaments, each coated with a micron-thick layer of natural silver. This plating of the yarn is done in Europe to ensure as high a quality finish as possible. In construction, 16 of these filaments are wound together to form an initial twist; two of these twists are then twisted together, and finally three of these twists are combined to form the finished thread. The conductive thread is approximately 18 denier. It is heavier than a regular sewing thread, but not as heavy as an upholstery thread. It can be sewn on most domestic sewing machines using either a regular needle or the next size up. This thread does not fray. Features: No (or very low) fray. Conductivity = approximately 40Ω per metre (12.2Ω per foot). Count = 875 dTex. Strength 3000 cN. Elongation at break = 37%. Twist = 240Z-380S. Contents: 1 x Reel Electro-Fashion®, Conductive Thread, 250m.

CHF 45.75*

Dettagli

LilyPad Sewable Electronics Kit

Con il kit LilyPad Sewable Electronics, potrete scoprire il meraviglioso mondo del cucito elettronico (e-sewing) e degli e-textiles attraverso una serie di progetti introduttivi che utilizzano il sistema LilyPad. Imparerete a cucire circuiti di base per far brillare i LED, a controllarli con pulsanti e interruttori e persino a sperimentare un circuito LilyMini pre-programmato che risponde alla luce ambientale. Oltre ai LED e ai portabatterie LilyPad, il kit include due schede LilyPad ProtoSnap per esplorare i circuiti prima di cucire i componenti in un progetto. Le istruzioni a colori per il kit LilyPad per l'elettronica da cucire (incluso) forniscono istruzioni passo-passo per l'utilizzo dei componenti LilyPad per creare quattro progetti completi di circuiti da cucire con filato conduttivo. Schemi facili da seguire e suggerimenti per la risoluzione dei problemi rendono questa guida un ottimo punto di partenza per creativi e artigiani. LilyPad è una tecnologia indossabile sviluppata dalla dottoressa Leah Buechley e progettata in collaborazione con SparkFun. Ogni componente di LilyPad è stato progettato in modo creativo con ampie cuciture in modo da poter essere cucito negli indumenti. Sono disponibili diverse schede di ingresso, uscita, alimentazione e sensori. Sono anche lavabili! Nota: una parte dei proventi della vendita sarà devoluta al dottor Buechley per l'ulteriore sviluppo e la formazione nel campo degli e-textiles. Progetti di elettronica da cucire: Progetto 1: Pin illuminato Progetto 2: Maschera illuminata Progetto 3: Peluche luminoso Progetto 4: Gagliardetto nocturno

CHF 185.00*

Dettagli

LilyPad LED Multicolore (6 colori)

This is the LilyPad Rainbow LED strip, with seven LilyPad LEDs that are still attached to one another, letting you snap LEDs apart at your leisure to sew into clothing or whatever else you can dream up. The LilyPad Rainbow LED features seven individual LEDs in six unique colors (Red, Blue, Green, Yellow, Pink, and White). Text has been added to the back of each board to indicate its color. Due to popular request, we have included two white LEDs instead of just one. Note: A portion of this sale is given back to Dr. Leah Buechley for continued development and education in e-textiles.

CHF 7.85*

LilyPad Licht Sensor

Der LilyPad Light Sensor ist ein nähbares Breakout-Board mit einem eingebauten ALS-PT19 Lichtsensor, der sofort einsatzbereit ist. Jeder Sensor gibt eine Spannung zwischen 0 V und 3,3 V aus, je nachdem, wie stark das Umgebungslicht auf ihn scheint. Je mehr Licht auf den Sensor fällt, desto mehr Strom fliesst von der Platine durch die Signalklemme zu dem Mikrocontroller, an den Sie den Sensor anschließen. Wenn kein Licht auf den Sensor fällt, fliesst auch kein Strom durch ihn. In einer typischen Beleuchtungssituation in Innenräumen gibt der Sensor etwa 1 bis 2 V ab. Wenn Sie diese Platine in Ihr nächstes E-Textil- oder Wearable-Projekt einbauen, eröffnen sich Ihnen ganz neue Möglichkeiten, da Sie die Fähigkeit zur Erfassung des Lichtpegels integrieren können. LilyPad ist eine tragbare E-Textil-Technologie, die von Leah Buechley entwickelt und von Leah und SparkFun gemeinsam entworfen wurde. Jedes LilyPad wurde so konzipiert, dass es über große Anschlusspads verfügt, um in die Kleidung eingenäht werden zu können. Es sind verschiedene Eingangs-, Ausgangs-, Strom- und Sensorplatinen erhältlich. Sie sind sogar waschbar! Übersetzt mit www.DeepL.com/Translator (kostenlose Version)

CHF 8.70*

LilyPad ProtoSnap Plus Kit

The LilyPad ProtoSnap Plus Kit is an all-in-one e-textile prototyping kit that has been specifically designed to make it as easy as possible to incorporate electronics into any of your garments or fabrics. The included LilyPad ProtoSnap Plus is a sewable electronics powerhouse that you can use to explore circuits and programming, then break apart to make an interactive fabric or wearable project. We have also included a USB cable, 110mAh LiPo battery, needle set and two conductive thread bobbins. With all of these parts combined and the featured Activity Guide (found in the Documents tab), you will be able to plan and create fantastic projects in no time! At the center of the ProtoSnap Plus is the LilyPad USB Plus microcontroller, pre-wired to a LilyPad board including a LilyPad Light Sensor, LilyPad Buzzer, LilyPad Button Board, four pairs of colored LilyPad LEDs and a LilyPad Slide Switch. Because these components are connected together on the ProtoSnap board, you can test out your project ideas before you sew. The ProtoSnap Plus also includes expansion ports that let you sew your wearables together or use alligator cables to easily connect external sensors and components. After testing out your coding ideas using the attached LilyPad pieces, you can break apart the prototyping board and sew them into your project! We have also written an online Activity Guide that teaches you how to program in Arduino with the LilyPad ProtoSnap Plus. This guide includes 10 example activities that use the pre-wired LilyPad boards on the LilyPad ProtoSnap Plus after you’ve completed the Hookup Guide linked below and in the Documents tab. Please be aware that the Lilypad ProtoSnap Plus Kit is NOT supported on Windows 7/8 due to a lack of support drivers for those specific OS’s. Note: A portion of this sale is given back to Dr. Leah Buechley for continued development and education in e-textiles and also to Arduino LLC to help fund continued development of new tools and new IDE features.

CHF 9.50*

Electro-Fashion Deluxe E-Textiles Pack

This deluxe E-Textiles pack is a great way to get a little more involved with E-Textiles. We have selected a number of products from our Electro-Fashion range, including three of our ultra-slim LEDs and two separate power boards. There are enough components for you get started immediately to create some eye catching E-Textiles projects, the only limit is your imagination. Features: Everything you need to complete three projects Enough Electro-Fashion components to get started immediately with E-Textiles Full instructions for assembly Great project ideas and tutorials Contents: 2 x Sewable Blue LEDs 2 x Sewable White LEDs 2 x Sewable Sakura (lilac) LEDs 2 x Blue Flashing LEDs 2 x Green Flashing LEDs 2 x White Flashing LEDs 1 x Slide Switch 1 x Push Switch 2 x CR2032 Coin Cell Batteries 1 x CR1220 Coin Cell Battery 1 x 6m Conductive Thread 1 x Coin Cell Holder 1 x Miniature Coin Cell Holder 1 x Switched Coin Cell Holder Dimensions: Ultra Slim Sewable LED Length: 15mm Ultra Slim Sewable LED Width: 6.5mm Ultra Slim Sewable LED Height: 2.7mm Slide Switch Length: 18mm Slide Switch Width: 8.5mm Slide Button Switch Height: 4mm Push Button Switch Length: 18mm Push Button Switch Width: 8.5mm Push Button Switch Height: 3mm CR1220 Battery Height: 2mm CR1220 Battery Diameter: 12mm CR2032 Battery Height: 3.2mm CR2032 Battery Diameter: 20mm Sewable Coin Cell Holder Length: 34mm Sewable Coin Cell Holder Width: 20mm Sewable Coin Cell Holder Height: 4.5mm Sewable Miniature Coin Cell Holder Length: 22mm Sewable Miniature Coin Cell Holder Width: 12.5mm Sewable Miniature Coin Cell Holder Height: 4mm Switched Coin Cell Holder Length: 22mm Switched Coin Cell Holder Width: 12.5mm Switched Coin Cell Holder Height: 4mm Requires: Scissors Needles

CHF 29.09*

Conductive Thread - 60g (Stainless Steel)

This is about 330 meters of conductive thread spun from stainless steel fiber and wound on a spool. You can use it as a creative way to connect various electronics onto clothing projects. This large spool is a great way to get into wearable electronics without a large upfront cost and a large enough quantity to not be afraid of making a few mistakes. What sets this thread apart from the other conductive thread that we carry is the fact that it's actually spun from stainless steel fibers (as opposed to plated silver) and doesn't have a Nylon core. This means that while it may not be easy to solder to, because it's stainless, it also won't burn up when you touch it with a soldering iron. Also, it's somewhat 'hairy' and can be slightly more difficult to work with in close, fine conditions than the other thread. Our resident E-Textiles expert suggests waxing the thread for hand sewing, as this should take care of any 'hairy thread' issues. Since waxing is impractical in machine sewing applications, avoid sewing close connections by machine as the 'hairs' could potentially short across small distances.

Contenuto: 330 Laufende(r) Meter (CHF 0.25* / 1 Laufende(r) Meter)

CHF 81.03*

Set di aghi

Info sui prodotti "Set di aghi"

Set di aghi

Info sui prodotti "Set di aghi"

Login