BBC micro:bit V2 - Kitronik Starter Kit

36.85 CHF*

Contenu : 1 Stück

Prix TTC, frais de livraison en sus

Plus disponible. Pour toute question, veuillez contacter notre hotline de service en bas de cette page.

Réf. produit : KIT-56104

Informations sur le produit "BBC micro:bit V2 - Kitronik Starter Kit"

Unlock your potential and get creative with code, electronics, science, and engineering

with the BBC micro:bit Starter Pack anything is possible!

This micro:bit V2 starter kit contains everything you need to get going with micro:bit straight away. It consists of a BBC micro:bit V2, a 1M anti tangle USB Cable, a Battery Cage and 2 x AAA Batteries. The USB cable allows you to connect your micro:bit to a computer. The battery pack and batteries enable you to power your BBC micro:bit once you disconnect it from the USB.

The starter pack is supplied in an organic bag that was designed for this purpose, features drawstrings, and can be used as permanent storage for the starter pack. It keeps your starter pack together and can be reused over and over again.

The new micro:bit V2 is the latest revision of everyone’s favourite powerful palm-sized, and fully programmable computer. Conceived by the BBC to encourage children to get actively involved in writing software and building new things that will be controlled by it. V2 is the same size, shape, and it works in the same way as the original micro:bit. So, if you have used the original then this will be instantly familiar to you. Write your code using one of the easy to use editors provided on the micro:bit website, connect your BBC microbit to your computer via USB, press the download button in the editor, and then downloaded the file to the micro:bit.

The BBC micro:bit is the spiritual successor of the BBC Micro of the 1980s, which itself introduced a generation of children to computing. The BBC micro:bit carries on this decades 30-year tradition and does it 18 times faster and it's also 70 times smaller than its predecessor.

Features:

The starter kit contains everything you need to get started with micro:bit.
This starter kit is supplied in an organic re-usable bag.
USB, Radio, serial, and Bluetooth Low energy connectivity.
A Compass and Accelerometer.
2 x user-assignable buttons.
A fully programmable 25 LED display.
25 pin notched edge connector.
Onboard speaker.
MEMs Microphone with LED indicator.
Touch-sensitive logo.
Light level sensing.
Temperature sensing.
Built-in sleep/off mode allowing the board to be powered-down with batteries connected.
A discrete regulator that can supply up to 200mA of current to external accessories.
Power status LED and USB data transfer LED.
Code it with MakeCode; Blocks, Javascript, or Python.

Contents:

1 x BBC micro:bit V2.
2 x AAA Batteries.
1 x Battery Cage.
A 1M Anti Tangle USB Cable.
An organic cotton storage bag.

Bildungsstufe:	cycle 2, cycle 2
DataLogger Schnittstellen:	BBC Micro:Bit
Fach:	informatique
Schnittstelle:	BlueTooth, USB
langue:	anglais

0 sur 0 évaluations

Laissez une évaluation !

Partagez avec d'autres clients votre avis sur le produit.

Connexion

Votre adresse e-mail

Votre mot de passe

Afficher les évaluations uniquement dans la langue actuelle.

Aucun avis n'a été trouvé. Partagez vos idées avec d'autres personnes.

Accessory Items

Enviro:Bit

Sense the world around you with enviro:bit! It's loaded with sensors for air and weather, colour and light, and sound, and slots right onto your micro:bit. Just slot in your micro:bit, then code enviro:bit with the block-based Microsoft MakeCode editor, or with MicroPython in the Mu code editor. The sensors go hand-in-hand really well with the LED matrix on micro:bit, letting you graph sensors readings or have the LEDs react to sound, for example. Features Comes fully-assembled and ready to use BME280 temperature, pressure, and humidity sensor TCS3472 light and colour sensor MEMS microphone Compatible with micro:bit Microsoft MakeCode and MicroPython support No soldering required!

3 013.00 CHF*

Détails

Kitronik :VIEW text32 LCD Screen for the BBC micro bit

The Kitronik :VIEW Text32 character LCD, for those times when the LED Matrix and/or external LEDs aren't delivering adequate visual feedback from your microbit project. The :VIEW Text32 is a character LCD showing 32 characters (2 lines of 16 characters). The :VIEW Text32 also breaks out the BBC micro:bit pins to edge pads (excluding pin14). The bottom edge of the board has a replication of the BBC microbits own edge connector, this allows you to plug the :VIEW Text32 into any board that the microbit itself can be slotted into. This is great news if your project outputs strings of text and numbers that previously would have slowly scrolled across the LED Matrix. The board has been designed so that the BBC micro:bit can be slotted into the edge connector on the top side of the PCB. No extra tools are required for installation, the board is supplied and ready to go --plug and play/work! On the back of the :VIEW Text32 is a 3 x AAA battery holder to provide power to the :VIEW Text32, the attached micro:bit, and the replicated edge connector. There is a power switch for turning the battery supply on and off. The replicated edge connector can supply 90mA (as per the normal micro:bit) Kitronik has produced a set of custom blocks for the Microsoft MakeCode editor. To add them click on the cog icon in the top right of the editor, then; select Extensions from the drop down menu, type and enter Kitronik into the search bar and select the :VIEW Text32 tile from the list. The custom blocks will now be added to the editor and can be used in your code. Features: The :VIEW Text32 is a character LCD showing 32 characters (2 lines of 16 characters). A BBC micro:bit can be slotted into the edge connector on the top side of the PCB. The board features a replicated microbit edge connector allowing it to be plugged into any board that a microbit can be slotted into. It features an on board battery holder that powers the display, the microbit and the replicated edge connector. The :VIEW Text32 can be coded with the Makecode editor or with MicroPython. Kitronik has created custom code blocks for the MakeCode editor to make using the :VIEW Text32 as simple as possible. Contents: 1 x :VIEW Text32 for BBC micro:bit. Dimensions: Length: 84mm. Height: 63mm. Thickness: 28.6.

40.00 CHF*

ZIP Halo for the BBC micro:bit

Add some colour to your next coding project with our new Halo board for the BBC micro:bit. The Halo has 24 ZIP LEDs, which are individually addressable full colour LEDs. This means that each LED can display a huge spectrum of colours, allowing amazing colourful effects to be achieved. The Halo bolts directly onto the BBC micro:bit using five bolts which are secure and robust. The board also has extension connector pads (0.1 pitch) allowing more ZIP LEDs to be connected. The P1 and P2 micro:bit pins are also broken out to 0.1" pads along with power and GND. This allows for additional connections to low power components such as sensors and switches. The Halo takes a supply voltage of 3.5V-5V and provides a regulated power supply to BBC micro:bit. Power can be connected using the JST input using a 3xAAA battery holder, or LiPo battery, or JST lead. Alternatively you can solder a power supply directly to the solder pads on the PCB. The LEDs used are based on the WS2812B part which is compatible with any WS2812B driver code. They can also be coded in the MakeCode Block/Javascript editor. Features: Halo has 24 individually addressable ZIP LEDs. Compatible with Adafruit NeoPixel and other WS2812B driver code. Supply voltage: 3.5V to 5V. Halo bolts directly onto the BBC micro:bit. The board also has extension connector pads. Contents: 1 x Halo for the BBC micro:bit. 5 x Counter Sunk M3 x6mm Screws. Dimensions: Diameter: 80mm. Height: 3.2mm Height With micro:bit: 10mm. PCB Thickness: 1.5mm.

1 558.00 CHF*

littleBits Micro:Bit Adaptor

The littleBits micro:bit Adapter connects micro:bit and littleBits enabling new learning experiences and creative inventions in a less-intimidating way. Enhance your learning with micro:bit by adding coding to your littleBits using platforms like the free Microsoft MakeCode or Python editor. It works by connecting the signals from the littleBits input and output bitsnaps to pins on the micro:bit edge connectors. No special coding libraries are needed. * micro:bit is required for use & sold separately

36.00 CHF*

micro:bit Enclosure (LEGO Compatible)

micro:bit LEGO enclosure is a protective case for micro:bit. It is specially designed by DFRobot, made by ABS material. It reserves A-B buttons and microLbit RST button, provides comprehensive protection. FEATURES Reserved A-B buttons and RST Button ABS transparent material LEGO compatible SPECIFICATION Size: 57.5x34.5x14.4 mm/ 2.26x1.36x0.57 inches Weight: 20g

41.00 CHF*

Détails

Monk Makes - Powered speaker board for micro:bit

The MonkMakes speaker for the BBC microbit is a neat little amplified speaker that connects to your microbit with crocodile clips. Despite its diminutive size, the speaker is quite loud. Features: Amplified Output. Integrated LED power on indicator. Reverse polarity protection. Contents:1 x MonkMakes Speaker Board for the BBC micro:bit. Dimensions: Length: 52.2mm. Width: 38.9mm. Height: 1.6mm. Requires: BBC micro:bit. Crocodile Leads.

15.55 CHF*

Détails

micro:bit Expansion Board for Boson (Gravity Compatible)

Die Erweiterungskarte verfügt über sechs 3-Pin-Buchsen, die mit Hunderten von DFRobot-modularisierten elektronischen Blöcken Boson und Gravity kompatibel sind. Die wichtigsten digitalen und analogen Sensoren und Aktoren abdecken und die Interaktion von Ton, Licht und Bewegung unterstützen. Darüber hinaus unterstützen die integrierte 3,5-mm-Kopfhörerbuchse und der Lautstärkeregler den direkten Anschluss des Kopfhörers. Um eine konstante Stromversorgung für diese Peripheriegeräte sicherzustellen, kann die Erweiterungskarte extern über den USB-Stromanschluss mit Strom versorgt werden.

135.00 CHF*

CO2 Sensor for micro:bit

This board, designed for use with the Lets Talk Science Living Space Project, provides a CO2, temperature and Relative Humidity measurements to a BBC micro:bit. Note, this item is a special order so lead times are a bit longer than usual. We include a 9V battery clip adapter with the CO2 sensor. (Battery not included).

150.00 CHF*

Environment Science Board for micro:bit

Environment Science Board for micro: bit is designed with highly symbolic trees, houses, and snowy mountains. On a wide and easy-to-use PCB, it integrates many sensor modules of nature and science. Including UV sensor, temperature sensor, humidity sensor, air pressure sensor, sound sensor, color sensor, light sensor, water temperature sensor, TDS water quality sensor, buzzer, OLED display, etc. This kit is rich in knowledge, including a wide range of applications. It is initial to observe and ease to play. Extended GPIOs are set and it supports gravity series sensors. The bottom is designed with PMMA (acrylic） to enhance the ease of use and durability. It supports Makecode and Mind + platforms. Power supply: 3.5V~5V (AAA 1.5V Battery x3) GPIO: P1, P2, P8, P12, UART, I2C ML8511 UV sensor BME280 sensor TCS34725 color sensor DS18B20 waterproof temperature sensor TDS water quality sensor Capacitive soil moisture sensor WS2812-RGB-LED Dimension: 196mm×110.6mm Programming platform: Makecode and Mind+

109.00 CHF*

Kitronik MI:pro Protector Case for the BBC micro:bit V1 & V2

Cet étui Kitronik MI:pro Protector Case pour le BBC micro:bit a été conçu pour fonctionner avec le micro:bit original V1 et le nouveau micro:bit V2 et s'inscrit dans la tradition de nos étuis précédents. Les étuis sont conçus pour garder le micro:bit en sécurité, entièrement utilisable, et pour offrir la liberté de ne pas être attaché à un ordinateur. L'étui est disponible en 4 couleurs différentes. Il s'agit de Clear (transparent), Blue (bleu), Green (vert) et Orange (orange). Les couleurs ne sont pas seulement esthétiques, elles peuvent aussi être utilisées pour différencier les étuis. Pratique ! Tous les étuis sont identiques à tous les autres égards. Si un porte-piles est fixé à l'arrière, l'étui peut également être posé sur un bureau et il comporte de grandes étiquettes faciles à lire pour les boutons A et B. Ce boîtier offre un accès complet aux broches inférieures du BBC micro:bit, ce qui permet d'utiliser la carte Edge Connector Breakout Board pour BBC micro:bit. L'une des principales caractéristiques du micro:bit est sa taille physique et cet étui a été conçu dans cette optique. Il est aussi compact que possible, tout en protégeant le micro:bit. L'étui est également fourni avec une pastille adhésive permettant de fixer un support de pile à l'arrière de l'étui, comme celui que l'on trouve dans notre kit de démarrage BBC micro:bit. Lorsqu'un porte-piles est utilisé, les projets micro:bit peuvent aller partout où vous allez. Même avec un porte-batterie fixé, la mallette reste de la taille d'une paume de main et portable.

5.19 CHF*

micro:Maqueen Plus V2 (4x AA-Batterien)

micro:Maqueen Plus is an advanced version of micro:Maqueen Lite (4.0), which is more powerful and intelligent. Optimized with better power management and larger capacity power supply, it can be perfectly compatible with HuskyLens AI Vision Sensor, which makes it an accessible AI robot teaching tool. In addition, micro:Maqueen Plus comes with a larger and more stable chassis, more built-in functions and more expansion ports, it is not only suitable for classroom teaching, but also can be suitable for after-school extended exercises and robot competitions. Note: micro:bit board und batterien nicht dabei. What’s new in Maqueen Plus V2? Two versions to choose from: 4 AA battery and 18650 battery New plastic box with a deeper base, enough room for the assembled car Frosted acrylic protective plate at the bottom, more durable and reliable The number of Line-tracking sensors has changed from 6 to 5, more convenient to program and optimize line-tracking codes Employs the motors whose parameters are the same as previous Maqueen, running steadily and smoothly Changes ultrasonic sensor to SR04, easier to install Add 4 RGB ambient lights at the base, RGB car lights have been changed to LEDs Delete the less usable magnetic encoder

7 064.00 CHF*

Détails

Moisture Sensor for micro:bit

The moisture sensor for micro:bit allows your micro:bit to detect moisture, so if your plant is thirsty you'll know about it! or how about using one and a couple of micro:bits to tell you when your bath has reached the correct level? To hook this up to your micro bit you will require alligator cables alternatively you can solder headers or a screw terminal to the board to make hooking it up to your other micro controller projects a dream.

1 449.00 CHF*

Détails

Kitronik :MOVE Motor for the BBC micro:bit

Le moteur Kitronik :MOVE pour le BBC micro:bit offre une introduction amusante à la robotique mobile. Plus qu'un simple véhicule programmable, apprendre à utiliser toutes les fonctionnalités incluses donnera au roboticien en herbe une base solide en robotique dans son ensemble. Requiert : 1 x micro:bit, 1 x câble USB de type A vers Micro-B en forme de nouille, 4 x piles AA.

45.00 CHF*

micro: IoT - micro:bit IoT Expansion Board

With the development of IoT, there are so many mature IoT platforms emerging in both domestic and overseas market, but most of them are mainly designed for the professional, which could be very hard for the non-experts to get started. Therefore, we specifically developed this micro: IoT, a micro:bit-based IoT expansion board. Use the board together with DFRobot Easy IoT platform, lower the barrier of using IoT. This micro: IoT board is pretty cute and delicate, on which we integrated Wi-Fi, OLED, 2-way motor drive, 6-way IO port, 2-way IIC, 1-way serial port, 1-way buzzer, 3-way RGB, 2-way servo, Li-ion battery holder, charging circuit, emergency power interface, etc. So many resources for you to program! Even without complicated background knowledge, you can build your IoT applications in few steps! We designed the board as a cloud shape to make it more suitable for the theme of IoT. As for power supply, we selected CR123A 3.6V lithium rechargeable battery. This kind of battery features small size, high capacity, and high safety. What’s more, we add short circuit and reverse connection protection for the product to further improve the safety in using Li-ion Battery. It's an easy-to-use and efficient IoT teaching tool, using this product, you can learn lessons related to IoT, such as:

60.25 CHF*

Kitty Case for micro:bit

Increase your micro:bit cuteness factor to over NINE THOUSAND with these soft rubber cases. They'll protect your micro:bit but still give you access to all of the ports, buttons, and lights. The Kitty Case is made from hard-wearing, soft, flexible rubber, making it a cinch to fit or remove it. The white piece lets you see the labels on the edge connector and access the pads with crocodile clips, or you can remove it altogether if you need to use the whole edge connector. You can access the three buttons, micro-USB, and JST connectors through cutouts in the case, and the rubber over the LED matrix diffuses the lights beautifully.

De 8.00 CHF*

Détails

Sensor Board for micro:bit

Description The MonkMakes Sensor Board allows you to detect sound levels, temperature and light levels. It features ring pad connectors for use with crocodile clips make it easy to connect to the board to a microbit. Sound Level:It senses sound level with a MEMs, which is a microphone on a chip that also features a pre-amplifier circuit. You can then use the plot bar graph block in the Microsoft MakeCode editor to display the result on the microbits LED matrix. Temperature Level:The temperature output from the board is a voltage that indicates the temperature. This is then measured using an analog input on the micro:bit. If you want your temperatures in Fahrenheit, then multiply the temperature in degrees C by 9, divide the result by 5 and then add 32. Light Level:The light sensor uses a photo-transistor to measure the light level and produces an output voltage that increases as the light level increases. It has 3V and GND connectors on both sides of the board which make it possible to power another board, such as the Relay Board or Powered Speaker Board. Features: 3V and GND connections can be made from either side and allow you to power a second board such as the MonkMakes Relay Board or MonkMakes Speaker. LED ‘power on’ indicator. Reverse polarity protection. All three sensors are analog and can be connected to pins P0, P1 and P2 using alligator clips. Detects sound level with a MEMs (microphone on a chip) and a pre-amplifier. Uses a thermistor to measure temperature. Light level detection with a photo-transistor (0 to 1023). All three sensors are analog and can be connected to pins P0, P1 and P2 using alligator clips. Contents: 1 x MonkMakes Sensor Board for the BBC micro:bit.

2 182.00 CHF*

Low voltage relay for micro:bit (solid state)

The MonkMakes Relay for the BBC microbit is a solid-state (no moving parts) relay that allows an output of a micro:bit to turn things on and off. A micro:bit can turn an LED on and off directly, but anything more powerful requires something like a relay or a transistor. Using a transistor to switch something on and off requires a shared ground connection with the micro:bit and a knowledge of electronics that you or your students may not be ready for. The MonkMakes Relay for micro:bit is much easier to use, acting like a simple micro:bit controlled switch. This relay can be used to switch low voltage devices such as light bulbs, a motor, a small heating element or even a string of 12V LED lighting. The voltage needs to be kept under 16V, but the relay will automatically protect itself against too much current. Features: Solid-state relay (No moving parts). Resettable polyfuse to protect against over-current. 2A Maximum current. 16V Maximum voltage. Integrated active LED power indicator. Contents: 1 x MonkMakes Relay Board for the BBC micro:bit. Dimensions: Length: 59.3mm. Width: 49mm. Height: 1.6mm. Requires: BBC micro:bit. Crocodile Leads.

187.00 CHF*

Grove Shield v2.0 for micro:bit

Das Grove-Shield für Microbit ist eine Plug-and-Play-Grove-Erweiterungskarte für Micro-Bit. Das Shield fungiert als Brücke zwischen dem Micro-Bit und dem Grove-System. Das Grove-System bietet Hunderte verschiedener Grove-Module, einschliesslich Sensor, Aktor, Kommunikation, Anzeigen usw., die den Umfang von micro: bit erweitern, um einfach und schnell mehr Projekte zu erstellen. Das Board verfügt über 4 Grove-Anschlüsse und bricht ebenfalls aus. GND, 3V, P0, P1, P2, P12, P13 vom Micro: Bit-Kantenanschluss, die Stifte 14 bis 16 und IC2 sind auch über die integrierten Grove-Anschlüsse verfügbar. Alle Nicht-Grove-Steckverbinder können entweder mit Krokodilklemmen oder 4-mm-Bananensteckern verbunden werden. Das Board verfügt außerdem über einen USB-Anschluss für die Stromversorgung des micro: bit. Dieses Grove-Schild ist das gleiche Board, das im Grove Inventors-Kit für micro: bit enthalten ist, das eine hervorragende Einführung in das physische Rechnen mit dem micro: bit bietet. Eigenschaften: Eine mit Grove-Systemen kompatible Micro: Bit-Schnittstellenkarte. Es verfügt über 4 Grove-Anschlüsse. Das Brett bricht aus; GND, 3V, P0, P1, P2, P12, P13 vom Micro: Bit-Kantenanschluss, die Stifte 14 bis 16 und IC2 sind auch über die integrierten Grove-Anschlüsse verfügbar. Die Nicht-Grove-Breakout-Punkte sind mit Krokodilklemmen und 4-mm-Bananensteckern kompatibel. Integrierter USB-Anschluss zum Einschalten Ihres micro: bit.

12.90 CHF*

Détails

Klimate Board for the BBC micro:bit

Add real-time clock and environment sensing (pressure, temperature, & humidity) capabilities to the micro:bit with the Kitronik RTC Board. MakeCode compatible.

2 805.00 CHF*

BBC micro:bit 10 Student Classroom Pack V2

Unlock your students potential to get creative with code, electronics, science, and engineering, with the BBC micro:bit Classroom Pack anything is possible! The BBC micro:bit V2 10 Student Classroom pack contains everything you need to deploy the micro:bit in the classroom. It consists of 10 x BBC micro:bit V2, 10 x 1M anti tangle USB Cables, 10 x Battery Cages and 20 x AAA Batteries. This buying option offers a better value way of obtaining multiple starter packs, making it an ideal choice for equipping a classroom. An individual starter pack contains everything you need to connect a BBC micro:bit to a computer and also enables you to power a BBC micro:bit once it is disconnected from the USB. The classroom pack contains 10 of these starter packs. The new micro:bit V2 is the latest revision of everyone’s favourite powerful palm-sized, and fully programmable computer. Conceived by the BBC to encourage children to get actively involved in writing software and building new things that will be controlled by it. V2 is the same size, shape, and it works in the same way as the original micro:bit. So, if you have used the original then this will be instantly familiar to you. Write your code using one of the easy to use editors provided on the micro:bit website, connect your BBC microbit to your computer via USB, press the download button in the editor, and then downloaded the file to the micro:bit. Features: The 10 student classroom pack contains everything you need to get your students learning straight away. The classroom pack consists of 10 x Starter Packs. USB, Radio, serial, and Bluetooth Low energy connectivity. A Compass and Accelerometer. 2 x user-assignable buttons. A fully programmable 25 LED display. 25 pin notched edge connector. Onboard speaker. MEMs Microphone with LED indicator. Touch-sensitive logo. Light level sensing. Temperature sensing. Built-in sleep/off mode allowing the board to be powered-down with batteries connected. A discrete regulator that can supply up to 200mA of current to external accessories. Power status LED and USB data transfer LED. Code it with MakeCode; Blocks, Javascript, or Python. Contents: 10 x BBC micro:bit V2. 20 x AAA Batteries. 10 x Battery Cages. 10 x 1M Anti Tangle USB Cable.

Contenu : 10 Paket(e) (28.60 CHF* / 1 Paket(e))

286.00 CHF*

Détails

CR123A Li-ion Battery Holder for micro: Maqueen

This is a Li-ion Battery Holder specially designed for micro: bit educational robot Maqueen. It can be used to hold a CR123A 3.6V lithium rechargeable battery to provide more than 8 hours continuous power for Maqueen. Using this environment-friendly product, you can save about 200 batteries in one year.This Li-ion Battery Holder integrates charging circuit and MicroUSB interface, freeing users from purchasing extra charger. Meanwhile, we set over-current and reverse connection protection for it to improve the safety in using Li-ion Battery. SPECIFICATION Charging Voltage: 4.5-5.5V DC Charging Interface: USB Output Voltage: 3.5~4.2V DC Reverse Connection Protection Over Current Protection Charging Current: 350mA Dimension: 56×32mm/2.20”×1.26” SHIPPING LIST CR123A Li-ion Battery Holder(V1.0) x1 Screw x4 Copper Column x4 Connecting wire x1 Double-side Adhesive Tape x1

10.35 CHF*

JST Jumper Wire and Socket

Il s'agit d'un simple câble à deux fils. Idéal pour passer d'une carte à l'autre ou à peu près n'importe quoi d'autre. Il y a un connecteur JST à 2 broches à une extrémité, le câble nu à l'extrémité opposée et il est également livré avec le connecteur correspondant pour le JST. Caractéristiques : Connecteur JST à 2 broches à une extrémité, câble nu à l'extrémité opposée. Livré avec le connecteur correspondant pour le JST que vous pouvez monter sur un PCB. Peut être utilisé pour concevoir d'autres options d'alimentation pour le microbit. Contenu : 1 x Fil de liaison et connecteur JST Dimensions : Longueur : 15cm.

177.00 CHF*

ZIP Halo HD for micro:bit

The Kitronik Halo HD board for the BBC micro:bit incorporates 60 individually addressable full colour ZIP LEDs. It also breaks out P1 and P2 to a standard 0.1” footprint, it features a MEMS microphone for detection of sound, and a piezo buzzer to play sound. If that weren't enough, it also features an onboard real time clock (RTC) controlled by I2C lines from the microbit. The board also has two M3 mounting holes. We think you'll agree, the board is loaded with useful features. It doesn't stop there... Plug n Play: No tools required, not even a screwdriver, plug the micro:bit straight into the onboard edge connector and you are good to go! Onboard Power: The board has a 3xAA battery holder mounted on the rear, with a power switch on the front of the board. A regulated supply is produced on the board which is fed into the 3V and GND connections to power the connected BBC micro:bit, removing the need to power the BBC micro:bit separately. See the Datasheet for more information. MakeCode Blocks: Kitronik have created custom blocks for the Halo HD for use with MakeCode. To add these blocks, first go to makecode.microbit.org and start a new project. Under the “Advanced” section click on “Extensions”. In the next window search for “Halo HD”. Then, click on the tile to import it into MakeCode. You will see that the blocks are split across three categories; ZIP LEDs, Microphone and Clock. You can find more information on the MakeCode editor and also on how to write code for it with MicroPython in the Datasheet. Examples: To get you off to a flying start we have produced a number of code examples that cover all of the onboard features and that will also serve to inspire your own projects. You will find links to these examples in the resources section below. Features: The board features 60 individually addressable full colour ZIP LEDs. It breaks out P1 and P2 to a standard 0.1” footprint. It's wired for sound with a MEMS microphone and a piezo buzzer. It has an onboard Real time clock (RTC) controlled by I2C lines. Plug n play with the onboard edge connector, no tools required!. The board has a 3xAA battery holder mounted on the rear. The On/off switch helps you maximise battery life. It can be coded with MakeCode blocks via our custom blocks or with MicroPython. 2 x M3 Mounting holes, for secure projects. Contents: 1 x :VIEW ZIP Halo HD Board for micro:bit. Dimensions: Diameter: 87mm. M3 Mounting Holes Spacing (Center to Center): 68.4mm.

30.00 CHF*

0.25W 8 Ohm 40mm Thin Speaker

This is the perfect speaker for projects that produce sound but where space is tight or where the speaker needs to be discreet. These speakers work well with the BBC microbit; you can code the microbit to play music or emit a beep as an alarm and this little speaker will do an admirable job. This a 0.25W, 8ohm speaker is only 40mm in diameter and just over 4mm thick making it very similar in size to those found in talking greeting cards, you could even design a microbit talking greeting card that has the built in micro:bit as a present as well as part of the card. Features: 8ohm speaker that is ideal for use with the BBC microbit. 4mm thick, making it ideal for use as a discreet speaker. Contents: 1 x 0.25W, 8ohm speaker. Dimensions: Diameter: 40mm. Thickness: 4mm. Requires: Soldering Iron. Solder.

2.05 CHF*

HUSKYLENS Pro

HuskyLens ist ein einfach zu bedienender AI-Vision Kamera Sensor, der auf ein Eigenbau Roboter angebaut werden kann. Er kann lernen, Objekte, Gesichter, Linien, Farben und Tags durch einfaches Klicken zu erkennen. Die Einstellungen kannst du einfach über die Bedienknöpfe vornehmen. Über UART oder I2C-Port kann HuskyLens eine Verbindung mit deinem Arduino, Raspberry Pi, LattePanda oder BBC micro:bit herstellen. Mit dem HuskyLens kannst du sehr kreative Projekte durchführen, ohne mit komplexen Algorithmen spielen zu müssen. DFRobot hat sich beim HuskyLens zum Ziel gesetzt, der einfachste AI-Vision-Sensor zu entwickeln. Du kannst verschiedene Algorithmen über die Bedienknöpfe ändern. Du kannst dem AI-Sensor auch neue Objekte lernen, die er dann detektieren kann. Info: HuskyLens ist neu auf dem Markt und es sind noch nicht viel Informationen und Programmierbeispiele vorhanden. Deshalb noch nicht für Anfänger geeignet.

71.68 CHF*

Environment Science Expansion Board V2.0 for micro:bit

This micro:bit-based expansion board, specially designed for STEAM education, allows students to measure environmental conditions for scientific experiments by using rich on-board sensors that cover all basic aspects of nature and science in daily life, which helps them explore the related science knowledge and understand nature phenomenon. It aims to provide a platform for students to learn science theory with practices and bring science education closer to daily life! Integrated sensors include UV sensor, temperature sensor, humidity sensor, air pressure sensor, sound sensor, light sensor, water temperature sensor, and a TDS (Total Dissolved Solids) water quality sensor, soil moisture sensor, TVOC, CO2 sensor, etc. FEATURESV2.0 Update Comes with WiFi-IoT card, support IoT platforms such as IFTTT, ThingSpeak, EasyIoT Supports for the measurements of TVOC and CO2 MicroUSB power supply port, battery holder is welded on the PCB, more convenient for classroom teaching Onboard 4-way RGB lights 1-way motor driver More powerful chip and more IO ports Greatly optimized OLED display program, more convenient and flexible to use The color sensor is removed from the list Product Features Highly-Integrated (14 function modules): atmospheric pressure, temperature, humidity, harmful gases(TVOC), carbon dioxide, ultraviolet rays, light, sound, water quality, water temperature, soil humidity, buzzer, RGB light, OLED display, and motor driver. IoT Function: able to be accessible to famous IoT platforms such as IFTTT, ThingSpeak, and EasyIoT through the WIFI-IoT card. The interesting shape of the tree makes the classroom teaching more vivid and fun.

174.53 CHF*

micro: Circular RGB LED Expansion Board

This board can be a cool clock, a timer, a Lucky Turntable Game, a wearable ornament, and an interactive colored pendant. With a micro:bit main board, this 24 RGB LEDs circular expansion board changes to an exquisite creator's piece. You can turn it into a tomato timer via the onboard buzzer, and turn it into a colorful music spectrometer through the onboard microphone; There are two external ports P0, P1 in reserve, so you can get more ways to play by connecting a large number of boson and gravity sensors. With different paper-cuts and acrylics, you can put on a variety of new clothes for the expansion board. For example, put on red Chinese knot for it in Chinese New Year, put on the cartoon face for it at Children's Day, put on the snow or Christmas tree for it at Christmas. FEATURES Support USB interface power supply and direct use of power-bank power supply or USB computer power supply. Support PH2.0 interface power supply and the battery box or lithium battery power supply are both OK. 24 RGB single-line lights, 16 million colors free mixing Makecode graphical programming Onboard microphone and buzzer Leaded out P0 and P1 interfaces, and distribute with the connection line, support the boson expansion modules. Ultra-thin volume,more suitable for wearable and strap applications.

1 558.00 CHF*

Crocodile Leads (set of 10)

Fünf Paar Krokodilklemmenleitungen (rot, schwarz, grün, gelb und weiss) mit Kunststoff isolierten 35mm Krokodilklemmen an jedem Ende. Länge 500mm. Drahtstärke 14/0,12 mm (22AWG). Maximaler Strom 0,5A.

Contenu : 10 Paket(e) (50.90 CHF* / 1 Paket(e))

509.00 CHF*

Détails

Kitronik Simple Robotics Kit for the BBC micro:bit

Plongez dans le monde de la robotique avec notre kit Simple Robotics et construisez votre propre robot piloté par Micro:bit, facile à assembler. Il a été conçu dès le départ pour être facile à monter, même pour les plus jeunes. Du châssis en carton d'une seule pièce aux connexions par clips, tout s'assemble de manière aussi peu frustrante que possible. Requiert : 1x BBC micro:bit, 1x tournevis, 1x paire de ciseaux.

31.00 CHF*

Math & Automatic Touch Keyboard for micro:bit

This is a Math & Automatic expansion board for micro:bit. Easy to use, and suitable for a wide range of applications. We designed this board for two sorts of application scenarios: math game and automation control. The 16 programmable touch keys and RGB LEDs on the board offers rich function and flexible input and output. Besides, the board has 1 vibration motor, 1 buzzer, 2 motor ports, 2 servo ports and 9 expansion ports, which lays a foundation for using in automation controlling application. FEATURESMath Game: 1.Calculator 2.Quick Calculation 3.Math Reasoning Game 4.Lucky number 5.Twenty-One 6.Whack a Mole 7.The mystery of Dazzling Numbers More...... Automatic Control: 1.RGB Waterfall Light 2.Touch Music 3.Password Lock 4.Motor Control System 5.Touch Remote Wireless Handle 6. Countdown Timer 7. Natural wind Electric Fan 8. NFC Password Entrance Guard 9. 2. 4G Multiplex Communication System More......

405.00 CHF*

Kitronik 16 Servo Driver Board for the BBC micro:bit

Take your robotics project to the next level with the (i2C) Kitronik 16 Servo Driver Board for the BBC micro:bit. Capable of controlling 16 servos which are powered directly from the board's power supply. The board can be powered either through the terminal blocks or the on-board header for radio control receiver packs. The pins from the BBC micro:bit are broken out to pads on the end of the Servo Driver Board, in accordance with the Link Standard for BBC micro:bit accessories. These pads can either be soldered onto directly, or they are the correct spacing for our PCB pin headers (see image below for a close up of the pads). Features: Input voltage 3V - 5.5V. Drive up to 16 servo motors. Servos take power directly from the board power supply. Standard 0.1" pitch servo connectors. Terminal blocks for easy connection of power. Includes Edge Connector for the BBC micro:bit to slot into. Link Standard compatible. Access the other BBC micro:bit pins easily and conveniently. Dimensions: Length: 67.4mm. Width: 62mm. Height: 16mm.

1 975.00 CHF*

Détails

Kitronik LAB:bit educational platform for BBC micro:bit

Le Kitronik LAB:bit pour le BBC micro:bit offre aux enfants une manière super amusante d'apprendre la programmation de manière engageante et pratique. Il a été spécialement conçu pour une utilisation en classe pour l'informatique de l'école primaire et est soutenu par des tutoriels en ligne MakeCode, des blocs personnalisés simplifiés et un guide détaillé pour bien commencer. Dans la boîte, vous trouverez un support de pile (3 x AA), une roue avec pneu pour le moteur, ainsi qu'un guide détaillé facile à suivre. Requiert : micro:bit, câble USB pour connecter le micro:bit à un ordinateur, 3 x piles AA, optionnel: Alimentation USB 5V.

43.63 CHF*

Détails